Book Services

What are your thoughts and feelings about How to Install a Bathtub?

Setting up a bathtub isn't precisely brain surgery, yet it does need solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is conveniently accessible, the project can move quickly; if you have to open a wall surface to eliminate the old tub as well as position the new bathtub, the task is much harder. In either case, the task is within a home handyman's abilities, although you will require an assistant to leave the old tub and also embeded in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable trying it. Instead of working with a service provider to take control of a halfway-completed task, it is better to think about employing one before you begin. Opportunities are you may need an expert plumber to make tube connections.
This post will certainly assist you mount a new tub in your washroom if you have currently acquired a new bathtub and don't require to change the setup of your previous water system pipes.
Your devices and material checklist must consist of the following:

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is detach the water supply. After doing so, turn on the faucets to drain any type of water staying in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the limited accessibility that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. When the supply pipelines have been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing substance.
Prior to moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

Fitting New Touches

If the tails of the brand-new taps are plastic, after that you will need a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers remain in location between the faucet and the sink. Safeguard the tap in place with the manufacturer given backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap ports. The former kind must be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

Mounting the Tub

Using the two wood boards under its feet, position the bathtub in the required position. The wood boards are handy in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 tiny points.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the tub until the level checks out degree.
To mount faucets, fit all-time low of the furthest adaptable faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Turn on the supply of water and also examine all joints and brand-new pipework for leakages and tighten them if needed. Load the tub as well as also examine the overflow electrical outlet and also the typical outlet for leaks.
Lastly, fix the bath paneling as explained in the manufacturer's instruction manual. Tiling and securing around the bath tub needs to wait until the bathtub has been made use of at the very least once as this will certainly settle it into its last position.

Getting ready for the Installment

To start with, the sustaining frame supplied with the bathroom ought to be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent strain on the tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath must currently be ready to be suited its last setting.

Tiling Around the Bathtub

In the area where the bathroom satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, triggering the water to pass through the wall surface in between the bathroom as well as the tiling, causing issues with dampness and also feasible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to permit the movement experienced when the tub is in use. The sealant can split rather very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue as well as grout.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I was introduced to that report about Tools You Need to Install a New Bathtub through a good friend on another blog. In case you liked our blog posting please don't forget to pass it around. Thank you for your time spent reading it.

Visit The Following Page